How to Fix Vacuum Cleaners

How to Fix Vacuum Cleaners - Repair and  Care 

Your vacuum cleaner doesn't need  much attention, but a little maintenance will keep it working and cleaning efficiently. Maintaining your vacuum cleaner properly can also head off costly repairs or even replacement. You can fix your vaccum cleaner easily.  You can repair it right at home.

Unplug your vacuum cleaner before performing any maintenance on it. A vacuum cleaner that turns on unexpectedly while you are working on it can harm you.

Check the bag regularly and replace it whenever it is full. A vacuum cleaner bag that is only 1/3 full may be too full to clean efficiently. Remember that the air must pass through all the collected dust and debris, so a full vacuum cleaner bag means that the machine must work harder, or that it will not clean as well, or both. Look for a line on the bag and feel with your hand to determine about how full it is.

If a working vacuum cleaner misses debris on the carpet or leaves behind fuzz where there was none, that's also a cue to check the bag.
Replace any vacuum bag that is 1/3 to 1/2 full. Read the directions carefully on the vacuum cleaner, the bag, or in the manual. Regardless of the procedure, make sure that the bag is on all the way and is secure, and that any clips or holders are in place.

Use the correct vacuum cleaner bag size and type for your machine.

Empty the bin or tray on bagless vacuum models frequently. Most designs make it very easy to pop the bin out.

Clean the brush roll. Also called a beater bar, this is the spinning brush underneath that brushes dirt out of the carpets.
\Look under the machine and locate the brush roll. Generally, it will be across the front of the bottom. If it is full of hair, thread, or other debris, it is time to clean it.

Remove the bottom plate. This cover may have clips or latches, or it may have a couple of screws holding it in place. Don't lose the screws.

Notice the direction that the brush roll goes in. Usually, there will be a belt on one side and a corresponding track or space on the brush roll for the belt. This will help you to identify the direction.

Remove the brush roll. Generally, it will pull out of a slot on either end, then slide out from under the belt.

Use scissors or your fingers to clean the brushes. They don't need to be spotless, but you should remove any hair or string that is wrapped around the brush. Pay special attention to the ends near the bearings and to the area around where the belt engages.

Clean and lubricate the vacum cleaner bearings on the brush roll.
Spin the brush roll on its axle with your fingers, to verify that it spins freely. If it doesn't, you may need to clean out the bearings more thoroughly, lubricate the bearings, replace the bearings, or replace the entire brush roll (in ascending order of expense).

Unscrew the cap on either end of the brush roll. You will need to hold the cap on the opposite end.
Remove any debris around and in the bearings. Before you take the bearings out, notice which way they went so you can put them back in correctly.

Remove the cap on the other end. Both caps are usually on one long axle, so you may need to hold the end of the axle still to remove the second cap. Clean and lubricate the bearing on the other end.

Replace both bearings in the direction that they were before and replace both end caps.

Check the vacuum cleaner belt for signs of wear, and replace it if it is worn.

Remove any cover plates on the bottom, as you would to clean the brush roll.

Pull on the belt with your fingers. It should be very tight.
Compare the belt to an unused belt. If it is stretched out or narrower than the new belt, replace it.

Check that the belt is in the right place. If it has slid off the drive shaft on its own or shifted out of position, it is probably because it is worn and loose.

Look for cracks, unevenness, or melted or worn spots.

Replace the belt every 6 months to 1 year, depending on how much use your vacuum cleaner sees.

Remove the brush roll as described above.
Slide the belt off of the pulley or drive shaft.
Slide the new vacuum cleaner belt on over the pulley or drive shaft.
Remove any large accumulations of debris from the air passages and the brush roll housing.
Replace the brush roll.
Put the brush roll back through the belt. It may be very tight.
Replace the brush roll in its slots. Make sure that the belt is still over both the brush roll and the drive shaft.
Replace the cover plates, reversing the process you used to remove them.

Replace or clean any filters on the vacuum cleaner. Many newer model vacuums have filters on the exhaust air to catch particles that remain in it. Read your manual to find out if yours has these, and clean or replace them periodically if it does.

If the filter is made out of foam or plastic, you may be able to rinse it clean. Make sure it is thoroughly dry before replacing it in the vacuum cleaner.

If the filter is made out of paper or fabric, you may be able to shake or pound out the debris between replacements.
Check the vacuum cleaner hoses for clogs and obstructions. It doesn't happen very often, but if you have lost suction, try pushing a broomstick gently through the hoses to dislodge any larger clumps of debris that are stuck. A hook made from bent coat hanger wire can also be used to pull out or loosen clogs.

Be careful not to pack clogs in even more tightly.
Handle a coat hanger wire carefully, or it could puncture the hose.

Do the following if you have a wet-dry vacuum cleaner:

Empty the bin rpften.

Replace or clean the filter periodically, according to how much you use the vacuum.

Know how to configure the vacuum for wet pickup, if you wish to vaccum up liquids. Make sure it is correctly configured for wet or dry use each time you use it.

General Vacuum Cleaner Tips, HInts and Secrets!

Perform maintenance proactively to prevent more severe problems.
Don't vacuum up large objects. Pick up trash, pennies, etc. with your hands or use a broom.
The power cord is a weak point on vacuum cleaners, so avoid getting it hung up on furniture, or other obstructions. Also avoid running over it with the roller brush.
Never run the machine to the end of the cord so that the plug pulls out of the wall outlet while the machine is running. This will cause an electric arc which will damage the prongs on the plug. It could also damage the cord.
Turn off your vacuum cleaner immediately if you hear or feel it struggling or if you accidentally roll over anything you shouldn't. An abrupt change in the loudness or the tone of the noise usually indicates a problem. Unplug it, check for and remove any obstructions, then plug it back in and listen carefully when you restart it.
Some vacuum cleaners have a device that stops the machine if it overheats. If your vacuum cleaner cuts out, unplug it, check your manual and wait for a period of time (perhaps 20 or 30 minutes). Then, check for obstructions or other problems, and carefully turn it on again.
On an upright vacuum cleamer with on-board tools, always insert the hose securely into its place when vacuuming floors. Any leak of air at this point will cost you cleaning power.
Visit your local vacuum cleaner repair shop for replacement parts or look online.
If your older vacuum cleaner works and you like it, keep it and take care of it. Vacuum cleaners are definitely one of those things that they don't make like they used to. (Also, despite the shiny, new packaging, there is very little new technology available.) If you decide to replace your vacuum cleaner, do your homework. Many of the vacuums on the market are not built very sturdily or strong.

Vacuum Cleaners - General Warnings

Always unplug a vacuum cleaner before working on it. The moving parts can cause injury, especially if they start unexpectedly.
Keep an eye on the cord for breaks in the insulation. If you see any breaks in it, and especially if you see wire through the outer rubber covering, do not use the vacuum cleaner until the cord has been properly repaired or replaced.
Do not use a vacumm cleaner outdoors or to vacuum liquids unless it is designed for this purpose.

Things You'll Need to Repair or Fix a Vacuum Cleaner

Vacuum cleaner replacement bags - make sure to get the right size
Screwdriver
Scissors
Vacuum cleaner replacement belts
Vacuum cleaner replacement filters